Chicken Feed Silo supplier

Chicken Feed Silo supplier

At present, the Chicken Feed Silo has a cylinder, square and rectangle. Under the same unloading area, the capacity of the dump is different, because the square bin is easy to form the dead angle at the junction, but the round is not bad, so the capacity of the round bin is the most, the square bin is the least, the rectangular bin is the smallest.today we will introduce Chicken Feed Silo supplier.

The artificial arch method, in general, is to reserve a number of holes in the inclined wall of the Chicken Feed Silo, and once the bunker is arched, that is, the tool is inserted into the bunker to move in the bunk, so that the arch will fall. The method is the most primitive, which has the advantages of simple design and low cost, but the effect of breaking arch is poor, and the labor intensity of manual dredging is great, it affects the time of production, the environment is easy to pollute the environment, and the automatic arch can not be realized, and after the material is dredged, there may be a large number of material underflushing and there is a great safety problem.

There are two basic forms of arch breaking by vibrating method, that is, material in vibrating bin wall and directly vibrating bin. The vibrating bin wall is installed on the silo wall of the cone part of the bin to vibrate the silo wall so as to achieve the goal of breaking the arch and clearing the warehouse.

For example, a pneumatic piston vibrator is used to vibrate the outer surface of the wall of a silo with a hammer; the electromagnetic vibrator is similar to that of the vibrator, both of which are vertical to the vibration of the barn, and the eccentric rotating vibrator is more complex. It is the vibration produced by the inertia force produced by the high speed rotating eccentric block to the wall to make it vibrate and compare with other types of vibrators. Its amplitude is small and its frequency is high.

The material in the direct vibration chamber is to stir the material to make it have better fluidity, or to crush the arch in the direction of the arch material.

For example, the vibration discharge device can not only break the arch by vibration, but also adjust the discharge amount of the material by changing the working parameters within a certain range. It is important to note that the vibrator is best linked to the silo gate or feeder when the mechanical vibration method is used to break out the storehouse, so that the vibrator works only when the gate is opened. If the vibrator works when the gate closes, the material at the bottom of the bunker may become more dense due to vibration, and it is more difficult to use the vibrator.

The pneumatic piston vibrator uses compressed air to drive the piston (hammer) to vibrate the wall. The principle of its working principle is that there is a piston in the vibrator and the inner air vent inside the piston. When the compressed air enters, the piston leads the gas to one end to produce thrust and pushes the cylinder to the other end. So the piston is used to make reciprocating motion in the body and transfer the vibration force through the body. When the piston is running, there will be a certain amount of compressed air at both ends. So the piston does not directly impact the body. The structure is simple, easy to use and low in price, but the vibration force is limited, and the storer will be damaged by the constant vibration wall, and the service life of the silo will be affected.

bolted oil storage tanks

Electromagnetic vibrators are powered by electromagnetic forces. The armature and hammerhead are integrated into one body. After the excitation coil is electrified, the armature is sucked into the iron core, and the hammerhead strikes the wall. When the power is broken, the hammer is reset by gravity or spring. Similar to the pneumatic piston vibrator, both of them are vibrating perpendicular to the barn wall, and the force of the silo wall is better, but there is also the problem of vibration force and noise.

The electric control eccentric rotation vibrator uses the eccentric force installed on the double outlet shaft of the motor to vibrate the wall with the centrifugal force generated by the rotation of the motor shaft. Because of the large and strong vibration force, the vibrator has better effect, but the noise generated is greater.

The eccentric rotary vibrator controlled by pneumatic is used to generate the vibrating force by the high-speed movement of the steel ball in the circular orbit. The main drawback of this type of vibrator is that the vibration force has a certain influence on the structure of the storehouse, and it may crack the wall of the silo, and the effect is not obvious for the high tenacity; the wear and corrosion of the vibrating plate is serious, and it is more troublesome to replace it. This method can be applied to small capacity conical hopper shallow barn.

Food storage tank

Chicken Feed Silo supplier

The blasting vibration method is often used to block the clogging location from the ground. Gas inspection must be carried out according to safety regulations before firing. The disadvantages of this method are poor safety, long preparation time, and frequent collapse of funnel or destruction of warehouse.

A shaft with spiral blades is arranged inside the Chicken Feed Silo, and is driven by the motor speed reducer. Through the rotation of the shaft with a helical blade, the material is dropped to the discharge port.

A porous plate is built in the cone of the Chicken Feed Silo, and the porous plate can be a metal, plastic, ceramic, multi-layer metal mesh, felt and other materials. The size and quantity of the plate can be selected according to the actual conditions.

The working principle is to ventilate the material when the material is discharged, so that the material is fluidization near the outlet to reduce the friction between the material and the inner wall of the silo. The ventilation in the storage bin is very effective in reducing the force between the particles and the effect of the particles on the inner wall of the silo. But for different materials, different pressure and volume of compressed air should be set. If the control is not good, it is possible to make the material overfluidization, resulting in an uncontrollable overflow from the storage outlet.

A row or several rows of nozzles are arranged on the outer wall of the cone of the Chicken Feed Silo supplier, and the compressed air passes through the electromagnetic valve and the filter nozzle into the silo, then changes the direction and spreads along the wall of the silo so as to clear the wall of the warehouse and make the arch material collapse. If the setting is reasonable, the effect of arch breaking is better. Otherwise, because of the air volume distribution, it may make some nozzles not work, and can not reach the effect of broken arch.

industrial food silos manufacturers in belgium

The broken arch of the air plugging device is the use of the gas that is stored in the gas storage bag to burst into the arch of the material directly and directly into the material. The blast force produced by the sudden outburst overcomes the static friction of the material and makes the material in the silo return to flow.