2018-06-26 18:03:26 By:NVirotech Bolted Tank (1491)
Enamel enamel equipment, such as tata bolt tank, is widely used in various fields, such as chemical, oil, printing and dyeing, pharmaceutical and food processing, because of its excellent corrosion resistance and high cost performance. However, in order to prolong the service life of tata bolt tank and give full play to the production efficiency of tata bolt tank, it is necessary to check the enamel reaction kettle regularly in addition to the manufacturer's attention in the selection of enamel reaction kettle equipment. Now let's talk about how to test enamel reactor regularly. I hope it will help you in the future maintenance of tata bolt tank.
The thickness of glass lined coating of tata bolt tank reactor is measured by porcelain thickness gauge (glass lined surface and nozzle part) frequently washed and discharged. The thickness of the glass lining is checked regularly, and the location of each inspection is constant. If it is detected by instrument testing, the thinning of the coating should be paid attention to, so as to prevent the greater loss after the explosion. If the glass coating is damaged, the necessary repairs should be made.
The inspector inspected the tata bolt tank layer visually (to see if solid particles were involved in the reaction to cause erosion and impact on the vessel wall). During the parking inspection, it is necessary to thoroughly clean the inner cylinder of the enamel reaction kettle, and require the inspectors to take any hard material in the case of safety and enter the inner cylinder of the equipment to examine the enamel coating and whether there is any chemical or mechanical damage to each part of the glass lining agitator, and see if there is any explosive porcelain. The occurrence of the phenomenon.
Secondly, strict control on the inspection period of tata bolt tank is needed. Its inspection cycle is shortened from one to two years.
First, check the quality of the mechanical seal (whether there are scratches on the end of the moving ring or static ring).
clean the O ring of the moving ring and the surface foreign body on the moving ring and static ring with clean soft cloth, and apply a little amount of lubricant to the surface according to the requirement of the medium in the tank.
uses the level and dial indicator to check the horizontal level of the mechanical seal static ring and the verticality of the sealing section of the mixing shaft, and calibrates the required requirements.
installs the fixed mechanical seal base and the fixed ring, and adjusts the six angle tightening screw in the fixed ring on the stirring shaft to make the mechanical seal spring uniformly force, so as to ensure the mechanical seal's dynamic and static ring end face close to the assembly to complete the test.
If the balance tank is fixed on the frame according to the requirement, the pipe of the seal liquid import and export and the mechanical seal is connected, the pipe of the nitrogen cylinder, the pressure reducer and the balance tank is connected. The test static pressure is fitted to the water jacket after the requirement is met, and the cooling water is used to test the car.
When the temperature of the tata bolt tank reaction tank is below 80 C, the type of refueling in the cooling tank should not affect the quality of the material in the tank. Generally, there should be high vaporization heat, clean no impurities and good lubricating function. When the medium temperature is higher than 80 degrees, the bottom cooling water jacket and cooling tank are cooled by circulating water.
The higher the circulating velocity of the hot oil in the tata bolt tank reactor, the higher the turbulence level, which helps to reduce its temperature distribution inhomogeneity in the furnace. To be precise, lowering the flow rate will aggravate the non-uniformity of heating oil heating, and the thermal degradation rate of heat conducting oil will accelerate.
Because coking is a non heat transfer substance, when the heat pipe oil is deposited on the wall of the hot oil furnace, the temperature difference between the inside and outside walls of the furnace tube is more than 300 degrees when the heat conduction oil 10mm is thick. That is to say, the hot oil temperature of the inner wall of the furnace tube is 300 degrees, and the temperature of the outer wall of the furnace is about more than 600 degrees. The furnace needs higher temperature, and the heat transfer can meet the requirement. High temperature will soften the tube of the hot oil furnace, and there is pressure in the tube, so the bubbling is produced on the tube, and the furnace tube is heated, bubbling, cracking and oil leaking. The fire is burning, burning hot oil and house, causing loss of human, money and material.
So the coking of heat conducting oil heating tube is the main reason for the fire of hot oil stove. Not to be ignored!
write down your requirement and contact details in the following form to get the latest price of this product within one day!
Hi, we intend to sell this website, if you are interested, please contact us:
Email:529733977@qq.com